House Painter Forum

Professional Painters => Professional Painters and associated Trades Forum => Topic started by: blackwolf on October 25, 2006, 05:18:29 PM

Title: very thick semi gloss trim paint(Glidden)
Post by: blackwolf on October 25, 2006, 05:18:29 PM
hello all,

i need some advice on thinning out semi gloss trim paint(Glidden), customer provided it, dries okay, however it's like molasses when applying it, even though I put very little on the 2" angled sash brush, I have a lot of trim left for next week and the windows in the foyer are 14 feet high, any way I need some advice as previously mentioned on thinning out this paint.

how much paint thinner per gallon or half gallon?  :-\


oh, I will take pictures, how do I put them on the forum?
Title: Re: very thick semi gloss trim paint(Glidden)
Post by: Flawless Finish on October 25, 2006, 05:54:40 PM
Is it the Evermore line? I've worked a lot with that in the past (not recently thought) especially doing trim. I actually like a little thicker paint for trim when putting a semi over a semi. That and I like using a little less stiff brush. When I use a thin paint on trim, I make a mess trying to get it to cover.
Title: Re: very thick semi gloss trim paint(Glidden)
Post by: blackwolf on October 25, 2006, 06:05:21 PM
yes it is the evermore line, i just need it a little thinner not runny, I did the same trim for my customer's mom using BM(my favorite) and I did not have this problem, semi over semi came out great and no hassles any way it's crusting up so fast I have to use 2 brushes, not at the same time, but alternating  any recommendation's on thinning?

 :-\
Title: Re: very thick semi gloss trim paint(Glidden)
Post by: Vin on October 25, 2006, 07:34:01 PM
I'd say add it slowly until you get the consistancy your looking for maybe start with a 1/4cup, shake it, see what you have, add more if neccesary.
Title: Re: very thick semi gloss trim paint(Glidden)
Post by: Jared on October 25, 2006, 08:18:03 PM
I believe the Evermore line is exclusively water based, so...

I'd recommend using Floetrol instead of water for the thinning - you won't sacrifice coverage ability for the thinner consistency.  ;)

(Always shake the Floetrol container vigorously before adding any of it to the paint - and always add small amounts at a time, paying attention to the maximum recommended proportions mentioned on the Floetrol container...  if you add too much, you'll need more paint to balance it out - so better to under-estimate the amount of Floetrol to add, always AVOID over-estimating the amount to add.)

If you are finding that the paint is drying a bit too fast to keep a wet edge, you could also (or instead) use some XIM Latex Extender, which also helps the coating self-level a bit better than without it.  Note that XIM Latex Extender is like water in consistency, and is quite a bit more potent than Floetrol - so much smaller amounts are recommended.  Again, follow the recommendations on the Latex Extender container for mixing proportions.

And remember these are options only for water-based paints - don't add these products to alkyds.  ;)
Title: Re: very thick semi gloss trim paint(Glidden)
Post by: rmichael on October 25, 2006, 09:30:06 PM
blackwolf
Break the paint out into two containers before you thin it. Thin one container to a workable level, I'd start with a few ounces (H20) and work up, if at some point you think you have over thinned , add in some paint from the other (un-thinned) container.
If you opt for a conditioner like Floetrol or XIM, add it and test first. You may or may not need to add a small amount of water to tweak the consistency. 
I prefer XIM to Floetrol, JMHO..

Best Luck
rmichael 
Title: Re: very thick semi gloss trim paint(Glidden)
Post by: blackwolf on October 26, 2006, 06:15:24 AM
Thank You!!
Title: Re: very thick semi gloss trim paint(Glidden)
Post by: Desy101 on October 30, 2017, 06:01:23 AM
Very well written information. Keep up the good work. Thanks.
192.168.0.1 (https://19216801.mobi/)